The update refers to the RAVENNA module used in MONTONE.42 and PRODUCER.COM (equipped with the module optionally).

** This update requires MONTONE.42 main frame firmware 2.0/1.9. **

Functions

• Please see the comprehensive Release Note document for changes in this update.

Major new functions:

• Network interfaces can be separately configured (IP/MAC/Gateway)
• Streaming and control can be assigned to a certain network interface
• Redundant audio streaming according to ST2022-7
• Many other little improvements

To run the firmware update please download the Dante Firmware Update Manager.

Before you update your device, make sure you have a backup of the device setup. After the update the device is required to reboot, so audio transmission will be interrupted.

Bugfixes

• fixed issues with 44.1 kHz operation
• includes latest firmware for Brooklyn module (v4.0.8.2)

Functions

Version 3.4

Functions

• New: Front panel brightness adjustable (Dim)

Bugfixes

• App hang if no DO.Net daemon was found on the network <- fixed
• ANDIAMO.MC - Gains: Channel no. above 99 were not displayed correctly

Bugfixes

• BLDS 1 LED did always blink in Pilote tone mode <- fixed

• Pilote tone mode did not work at 96kHz <- fixed

The update refers to the RAVENNA module used in MONTONE.42 and PRODUCER.COM (equipped with the module optionally).

** This update requires MONTONE.42 main frame firmware 2.0/1.9. **

Bugfixes

• Payload size did not match the value in stream configuration <- fixed

Update 18.10.2017 - black & green front panel version.

Before you update your device, make sure you have a full config backup of your data. During the update the device will reboot, so audio transmission will be interrupted.

The update procedure is described on page 32 of the Hardware & Installation Guide.

Functions

• SW-P 08: added live debugging
• SW-P 08: matrix IDs freely configurable
• Improved Tally handling
• SW-P 08: added system snapshot and system script matrix
• SW-P 08: added Label im-/export
• improved label import/export help page
• luad: added telnettx, tcptx, udptx, sertx
• added separate system script window

Bugfixes

• Doppelgaenger slave discovery
• Configuration restore in green series broken
• Watchdog did not restart httpd anymore since 2017-08-09
• multi-line comments in snapshots got cut off
• some special characters in channel labels were not masked properly

Version 3.3

Bugfixes

• Remote window not displayed after device Enumeration via DO.Net <- fixed
• ANDIAMO.AES Remote window not displayed after Enumeration <- fixed
• Offline Mode did not work as of version 3.2.1 <- fixed

Update 30.08.2017 - black & green front panel version.

Before you update your device, make sure you have a full config backup of your data. During the update the device will reboot, so audio transmission will be interrupted.

The update procedure is described on page 32 of the Hardware & Installation Guide.

Functions

• service web page (for updates, support) running with autonomous webserver on port 8080

Bugfixes

• Masking of " missing in function that displays the currently active snapshot <- fixed
• snapshots which changed FS might have had not all XPs restored <- fixed

The update refers to the RAVENNA module used in MONTONE.42 and PRODUCER.COM (equipped with the module optionally).

** This update requires MONTONE.42 main frame firmware 2.0/1.9. **

Functions

• HTML-based web interface
• Popup windows to edit related settings (e.g. MADI Out) accessible via hyperlinks 
• Info display via mouse-over (e.g. PSU)
• Scalable GUI (lossless zoom) for optimal view on standard or hdpi display
• Matrix: View Filter added to hide unused I/Os
• Matrix: N/C line added (Not Connected)
• Matrix: SHIFT + Click for multi-channel-patches (diagonal and horizontal)
• Matrix: ALT + Click to de-activate a patch (set to N/C)
• Lock device: Password protection
• PTP profiles: default E2E, default P2P, media E2E, media P2P, customized
• Display of Grandmaster ID (GMID)
• Gateway support for static and dynamic IP addresses
• Support of SMPTE/ST2110-30

Version 3.2

Bugfixes

• Wrong device selected after first device enumeration <- fixed.

2 FS signals may use either the 48k Frame (S/MUX) or the 96k Frame (sometimes called ‚high speed‘) format. MADI.9648 detects the frame format at the 2 FS input and sets the 2 FS output accordingly.

Functions

- added support for 48k Frame (S/MUX) at the 2 FS I/Os. 

Update 09.06.2017 - black & green front panel version.

Before you update your device, make sure you have a full config backup of your data. During the update the device will reboot, so audio transmission will be interrupted.

The update procedure is described on page 32 of the Hardware & Installation Guide.

Functions

• added check of gateway IP (which is mandatory in manual IP configuration)
• added warning if IP reset is disabled
• added tally functionality to scripts
• added SYSTEM_SCRIPT to telnet
• added MIDI controller B8 to load system snapshots
• improved transaction speed on audio xp lock & gain lock
• delayed network configuration to a point after initialization
• removed PORTGAIN_MODE command from telnet

Bugfixes

• disabled automatic 57ch switch did not let turn off 57ch mode manually
• large config backup generation could lead to browser time out while waiting for download; now generating uncompressed configuration backup archives

Update 03.05.2017 - black front panel version

Before you update your device, make sure you have a full config backup of your data. During the update the device will reboot, so audio transmission will be interrupted.

The update procedure is described on page 32 of the Hardware & Installation Guide.

Functions

Bugfixes

• 57ch mode was sometimes greyed out and not switchable manually <- fixed

Functions

Functions

Update 20.03.2017 - black front panel version

Before you update your device, make sure you have a full config backup of your data. During the update the device will reboot, so audio transmission will be interrupted.

The update procedure is described on page 32 of the Hardware & Installation Guide.

Functions

A new version (1.5) of ANNA-LISA Remote for ANDROID is ready for download in the Google PlayStore.

Functions

• New: 57 channel mode (in Expert Mode)
• SFP and Channel Status freshened up
• FPGA Firmware 1.6

Bugfixes

Update 23.02.2017 - black + green front panel version

Before you update your device, make sure you have a full config backup of your data. During the update the device will reboot, so audio transmission will be interrupted.

The update procedure is described on page 32 of the Hardware & Installation Guide.

Bugfixes

• fixed display problem of port/serial/MIDI matrix on hiDPI displays
• fixed display problem of MADI channels in port configuration page
• added workaround for update problem in port matrix after loading a snapshot

Functions

• support for macOS® 10.12.x (Sierra)

Firmware 2.5 features a De-Embedder / Embedder for serial data

Functions

Bypass for embedded serial data (Serial over MADI)

Update 01.02.2017 - black front panel version

Before you update your device, make sure you have a full config backup of your data. During the update the device will reboot, so audio transmission will be interrupted.

The update procedure is described on page 32 of the Hardware & Installation Guide.

Functions

black version:

added fallback mode to fan controller

"Plugin Configuration" page added to online help

BETA: LUA scripting engine (public beta) <- not yet recommend for use in productive environments.

Bugfixes

three byte SysEx messages entered in MIDI Tool were not transmitted <- fixed

linux kernel's w1_therm driver could segfault <- fixed

typos in output of telnet daemon <- fixed

Functions

New:

GPI Fault detection: If one or more GPIs has contact to GND, the respective yellow LED in the center of the unit flashes quickly during power up.

Mute output with GPI 1 and 2

Connecting GPI 1 and GPI 2 to GND mutes output

Audio Pilot modes:

Presence of audio signal > -42 dBFS on channel 56 (96kHz: ch. 28) triggers switching. Switching to the port is immediate, switching away after ca. 10 ms. The pilote tone modes are indicated by slowly blinking LOCK LEDs in the Priority section.

Version 1.17 of the Firmware for DirectOut PRODUCER.COM is released.

Functions

Clock Multiplier (1FS, 2FS, 4FS) follows word clock automatically if WCK is selected as sync source.

Update 19.12.2016 - black front panel version

Before you update your device, make sure you have a full config backup of your data. During the update the device will reboot, so audio transmission will be interrupted.

The update procedure is described on page 32 of the Hardware & Installation Guide.

Functions

black version:

• port configuration page now remembers last selected port
• system script tab added to mobile page
•  BETA: LUA scripting engine (public beta) <- not yet recommend for use in productive environments.

Bugfixes

• bug in CSV routing export function <- fixed
• DONET daemon always disabled after reboot <- fixed
• improved storage of device registration data

Bugfixes

- issue with remote control for Yamaha AD8HR (Remote Protocol C) <- fixed

Version 3.0.2

Bugfixes

• AD/DA Calibration dialog updated for use with ANDIAMO.MC
• AD/DA Calibration activation did not work reliably <- fixed
• GUI error on Fastswitch buttons in Gains windows <- fixed
• ANDIAMO.MC with Dallis firmware did not appear on Fastswitch buttons <- fixed

Update 28.11.2016 - green & black front panel version

Before you update your device, make sure you have a full config backup of your data. During the update the device will reboot, so audio transmission will be interrupted.

The update procedure is described on page 32 of the Hardware & Installation Guide.

Functions

green version:

- support for SDHC cards added (please install SDHC update first!)

black version:

- smart SFP.IO board support added

- BETA: LUA scripting engine (public beta) <- not yet recommend for use in productive environments.

Bugfixes

- Display error in Channel Matrix overview display <- fixed

LUA Scripting Engine (BETA):
- formatting in scripting help fixed
- missing scripting directory added

Functions

New Feature:

- Remote Control via MIDI Program Changes

Bugfixes

- phase reverse issue at analog output (only devices with new DA converters) <= fixed

Bugfixes

- phase reverse issue at analog output (only devices with new DA converters) <= fixed

Bugfixes

- phase reverse issue at analog output (only devices with new DA converters) <= fixed

Bugfixes

- phase reverse issue at analog output (only devices with new DA converters) <= fixed

Functions

- User Bit Transport automatic set to ‚REM‘ in the background, if the USB Embedder is active

The new features are accessible with ANDIAMO Remote v3.0 (Windows®) or higher.

Functions

- new: defeat delay compensation

- modified: level meter: low level start @ -60dBFs

Bugfixes

- issue with device activation < fixed

- issue with embedder for MIDI-over-MADI < fixed

Version 3.0

Functions

• Switch to deactivate Delay Compensation added.
• Improved UI update when switching between devices.
• Fast Switch buttons in Gains window allow switching between up to 4 devices. The device name on the button is taken from the device name given in the Device Manager.
• Project Files allow to save and restore settings of all currently connected devices. Missing units will be skipped when loading a project file.
• Snapshot function for gain settings. A snapshot contains all gain settings of all currently connected devices.
• New program setting to deactivate click&drag behaviour in the matrix. Only one crosspoint is set at a time.

Bugfixes

• Settings dialog: 'Cancel' still changed settings if the device's status had not been queried before (e.g. when switching to the second unit in a chain). <- fixed. Also settings dialog can not be accessed until the current status has been queried successfully.
• Devicelist file could not be saved under certain circumstances <- missing user rights to write file in program file directory -> Devicelist is now stored in /AppData directory.
• Redundancy Settings: 'Force to MADI x' got changed to 'Prio to MADI x' if 'Force to MADI x' was already selected before. <- fixed
• Transmission of current settings when switching from offline mode to online mode does not work as expected <- This function is not compatible anymore with the way how multiple devices are enumerated. It has been replaced by a request to save a preset file.

Functions

New:

- improved Muting on power on / power off as of hardware revision 1.2

Bugfixes

- Menu navigation corrected

- Phones out: phase reverse corrected

Bugfixes

- Menu navigation corrected

- Phones out: phase reverse corrected

Version 1.6 of the Remote Software for DirectOut PRODUCER.COM is released.

Functions

Aux Output routing now supports busses as source (e.g. talkback or listen).

Version 2.8.2

Functions

• Extended Routing did not work with ANDIAMO.MC that use firmware version 4.x <- fixed
• DO.Net - modified TTL value (128) to address issues in networks environments with more than one switch.