DirectOut PRODIGY.MC - Changelog 2023-12-19 ************************ Build 35 (19.12.2023) Features - support for MADI2.BNC.SRC.IO Changes - AN8.O 2.0 - use fast Roll-off filter to avoid frequency issues above 18kHz (latency ~30 samples) Bugfixes - Net mask CID translation did not work properly - replaced wrong automator binary - front panel: improved behaviour of snapshot list ************************ Build 34 (17.10.2023) Features - Link Local Address support if DHCP is not answering (zeroConf) - AES Output Dark - automator: link faders between devices - HOME support prepared - support for MADI2.BNC.SRC.IO - MIDI Tunnel for SG.IO (available in MIDI Matrix) Changes - FPGA: Userbit transparency for NET slots with inactive AM824 setting - cored: increased number of possible connections - cored: improved log output - Improved stability of firmware updates of NET modules with SRC Bugfixes - FPGA: MTC 30fps - FPGA: MADI Slot 2 Sample rate factor information fixed ************************ Build 33 (25.05.2023) Features MADI2.SFP.IO support SNMP support Changes FPGA/cored: improved configuration for modules with ESS ADC converters autoupdated: improved stability of NET.BASE.SRC module firmware updates Bugfixes FPGA: MADI Mode Legacy/Highspeed swap corrected ************************ Build 32 (19.12.2022) Features Front Panel: Display Timeout and Brightness control Input Slot Labels Recall Snapshot 1/2 with GPI 1/2 (support for HCONTROL.8 via globcon/GLUE) Bugfixes FPGA: improved FastSRC FPGA: BLDS detection for 96k and 192k frame mode Ember+: fix for crash after many connection attempts Triggers would trigger always on device startup Gateway Information Fix for bit transparency mode in combination with ESS ADC modules improved configuration of ESS DAC modules to prevent unwanted muting ************************ Build 31 (2022-08-17) Crossfade for Groups Reset device without removing snapshots Group crossfades for Ember+ service Reduced delay for ESS DA converters HOME button pressed for 30 seconds also restarts web server Automator (Settings/Licenses) ************************ Build 30 (2022-05-18) improved snapshot load behaviour in config mode: automatic MUTE ALL is applied on recall WCK Out can be fixed to 1FS or Follow FS (Follow FS was previous behaviour) MADI High Speed mode for 4FS (switchable) MADI Output Dark EARS with Disaster Recovery Input Mutes Ember+ with Levelmeter Support improved warning messages for PSU failure and power over-consumption added dynamic measurement of power consumption to allow usage of more than 6 MIC8.HD modules display and configuration of RAV.IO IP addresses ************************ Build 29 (2021-12-22) New Features support for analog I/O modules Rev 2.0 Bugfixes unnecessary error messgaes by MirrorMode service <- fixed Hush wizzard value was not applied after reboot <- fixed ************************ Build 28 NOTE: This release requires globcon version 1.8.0. Build 26 needs to be installed first, if the device shall be updated from an earlier version (< build 26). New Features Summing Busses (PRODIGY.MC - Advanced or license bundle FastSRC) MirrorMode User definable slot labels Changes Confirmation dialog on snapshot page if snapshots are loaded in CONFIG mode Improved support archive information Fixes fixed issue with blocked License Manager Ember+: improved gain value representation ************************ Build 27 NOTE: This release requires globcon version 1.7.0 and Build 26 being installed first. NOTE: globcon version 1.7.0 needs to be downloaded from www.globcon.pro - it is not updated automatically from an earlier version installed. New Features Input Managers with silence detection Automatic Bypass for FastSRC(TM) Loudness Metering (license option) ************************ Build 26 NOTE: This release requires globcon version 1.6.0 New Features Front panel: signal present indicator in levelmeters aligned with globcon levelmeters Front panel: license information page with info about license state on the device Remote control: Ember+ service Remote control: OSC service Fixes Front panel: levelmeter flickering with static signals (e.g. sine wave) <- fixed Front panel: graphical module label wrap-around for certain module types <- fixed ************************ Build 25 NOTE: This release requires globcon version 1.5.0 New Features Snapshots can be stored in the device and recalled stand-alone from the front panel "Configuration" and "Show" Mode Ember+ OSC Changes Improved MADI receiver Improved file handling for configuration data ************************ Build 23 New Features GROUPS: Outputs can be assigned to up to 16 groups basic MIDI-over-MADI control support (Gains, P48, PAD -> use PRODIGY MIDI PlugIn in globcon) improved Fan speed measurement Bugfixes improved DA Mute during power-on AoIP modules could be set and held in reset state after several weeks without reboot <- fixed FrontPanel: Output Levelmeters did not work <- fixed FrontPanel: Phones Mute Button was not updated correctly in all cases <- fixed ************************ Build 22 New Features Fast SRCs (bidirectional low latency asynchronous SRC) for MADI and NET I/Os MIDI-Matrix (incl. support for MIDI-over-MADI tunneling) LTC to MTC converter Sine wave, Pink noise and white noise generators Enhanced Automatic Redundancy Switching (EARS) for NET and MADI I/Os Levelmeter speed configuration Bugfixes Lock state not preserved on page reload via Browser <- fixed Bit transparency for ST2110-31 and AES I/Os did not work properly <- fixed improved globcon bridge startup behaviour ************************ Build 21 New Features Front panel: Locking function with PIN entry and auto lock Front panel: optional home view with big LTC display (tap on LTC to activate) Auto clock algorithm for automatic sync source changeover Fan control with setting for temperature threshold and silent mode Transparent mode for MADI and NET I/Os for ST2110-31 support IMPROVEMENT: Update now preserves network interface configuration Bugfixes Front Panel: Front panel: clock source on home screen was not updated correctly under certain circumstances Front panel: encoder turn did not work anymore when display was released from idle state via tap on the screen ************************ Build 20 Issues Resolved: BUGFIX: Phase reverse fix of FPGA build 66 affected AES outputs also Changes: Improved idle Display behaviour -> if the screen is dark the first tap on the screen, encoder movement or pressing a button is ignored and just turns on the backlight Improved Watchdog ************************ Build 19 Issues Resolved: BUGFIX: 64ch Mode for MADI I/Os did not work properly at 2FS and 4FS BUGFIX: AN8.O Line Outputs were phase reversed BUGFIX: Gain Range of MIC8.LINE modules was not completely available BUGFIX: AES LED still showed blue color for clock master even if there was no input signal available New Features: added downloadable Support Archive added watchdog for front panel UI added PAD initialisation during boot ************************ Build 18 Issues Resolved: - Gateway setting was not restored after reboot on UI <- fixed - noise on Headphone Outputs @4FS <- fixed - improved DANTE.IO boot behavior New Features: - support for all MIC modules