DirectOut MAVEN.A - Changelog 07.10.2025

****************************
Build V25.08.2 (07.10.2025)

Bugfixes:
- Reset to 'factory defaults' when updating directly from version 0.* (i.e. before 25.04.1)


****************************
Build V25.08.1 (29.08.2025)

Features:
- SNMP
- LLDP
- Ember+
- Mirror Mode (device-specific certificates are required and available at https://mirrormode.directout.eu - install certificate via 'Live Installer'.)
- Recall Snapshot 1/2 from front panel

Bugfixes: 
- globcon: firmware version of MADI4.SRC.IO / MADI4.IO displayed as 1.0b17 instead of 1.0b11, this is only a cosmetic issue.
- globcon: discovery name was wrongly displayed
- the update webpage can be white in some cases

Known issue:
- Ember+: missing device_info/model

Missing Features: 
- Loudness Metering 
- OSC 
- Lawo HOME 
- Demo mode for licenses



*** NOTE! ************************************************ NOTE! ***
The system update may take up to 1 hour. 
During this time, the device will reboot several times. 

The browser window might loose connection during this time. 
The front panel will show a “Update in Progress” indication though. 

Do not switch off the device during the update process. 

When the update is finished, the browser window can connect 
to the device again and display the “Live Installer” window.

During the update browser might display a white page.
Reload the page bypassing the cache (hard reload).
https://en.wikipedia.org/wiki/Wikipedia:Bypass_your_cache
*** NOTE! ************************************************ NOTE! ***


****************************
Build V25.04.8 (07.07.2025)

Bugfixes: 
- MIC8.HD.I / MIC8.LINE.I gain is not working as expected <= fixed 
- Level meters of IO modules in Slot A are not reported properly <= fixed 
- MADI4.SRC.IO / MADI4.IO not booting after cold restart <= fixed 
- MADI4.SRC.IO / MADI4.IO configuration not restored properly after restart <= fixed 
- Update from 0.1.7 may cause device lock <= fixed

Known issue 
- globcon: firmware version of MADI4.SRC.IO / MADI4.IO displayed as 1.0b17 instead of 1.0b11, this is only a cosmetic issue.

Missing Features: 
- Loudness Metering 
- Ember+ 
- SNMP 
- OSC 
- Lawo HOME 
- Mirror mode 
- Demo mode for licenses


****************************
Build V25.04.4 (06.05.2025)

Bugfixes:
- device not booting properly after update <= fixed
- no ip address assigned at initial launch of a new device <= fixed
- issue with automatic reboot during update <= fixed
- Shutdown/Restart/Update from globcon <= fixed

Missing Features:
- Loudness Metering
- Ember+
- SNMP
- OSC
- Lawo HOME
- Mirror mode
- Demo mode for licenses


****************************
Build V25.04.1 (24.04.2025)

*** IMPORTANT! ************************************** IMPORTANT! ***

This update will perform a RESET to factory defaults of the device.
Save your project in globcon before running the update.

*** IMPORTANT! ************************************** IMPORTANT! ***

Bugfixes:
- Encoder: not working to set brightness and phone levels

Features:
- Update Mode: "Update in progress..." is shown on the front panel during the update
- Single file to update Maven
- Licenses: install license pack (one file including all licenses)

- Channel based routing
- LTC reader 
- FastSRC - MADI
- FastSRC - Slot A
- Bypass FastSRC when HD SRC is enabled

- Clock Redundancy
- MADI Redundancy for built-in MADI ports
- EARS
- Automix
- Automator

- 64x64 MatMix
- 64 Summing Busses
- 64 Flex-Channels
- 16 FIR EQs
- Custom filter available
- 64 IIR EQs
- 64 Dynamics
- 64 Delays (32 @ 4FS!)
- 32 Input Managers

- Snapshots
- Front panel: extended menu
- Support of MADI4.IO, MADI4.SRC.IO, MADI2.SRC.IO, MADI2.BNC.SRC.IO


Missing Features:
- Loudness Metering
- Ember+
- SNMP
- OSC
- Lawo HOME
- Mirror mode
- Demo mode for licenses
- Shutdown/Restart/Update from globcon

Known issue:
- Custom filters are not stored in Snapshots