Skip to main content
06.07.2020

PRODIGY.MP System Update Build 9

This system update replaces the entire system to build 9.

This release requires globcon version 1.3.0

Please follow the update instructions in the Manual.

Functions

  • Fast SRCs (bidirectional low latency asynchronous SRC) for MADI and NET I/Os
  • 32 IIR Filters offering the combination of two filters selectable from All Pass, Low/Hi Pass, Low/Hi Shelf, Peak, Notch, Band Pass, Gain, RIIA Production/Playback
  • Enhanced Dynamics with Mono/Stereo Link, Side Chain and Parallel Compression
  • Added 32 Input Managers, with Signal Lock and selectable Level Coherence detection, selectable STEREO Link behavior, Sources auto level trim tool
  • MIDI-Matrix (incl. support for MIDI-over-MADI tunneling)
  • LTC to MTC converter
  • Sine wave, Pink noise and white noise generators
  • Enhanced Automatic Redundancy Switching (EARS) for NET and MADI I/Os
  • Levelmeter speed configuration

Bugfixes

  • Lock state not preserved on page reload via Browser <- fixed
  • Bit transparency for ST2110-31 and AES I/Os did not work properly <- fixed
  • improved globcon bridge startup behaviour
10.06.2020

EXBOX.MD - Firmware 1.6

To run the firmware update please download the Dante Firmware Update Manager or you may use the update function which is integrated in the Dante Controller.

The firmware update procedure is described in the manual (Appendix D).

Before you update your device, make sure you have a backup of the device setup. After the update the device is required to reboot, so audio transmission will be interrupted.

Functions

  • Fast SRC for Dante I/O
  • new VLAN configurations for control on port 4 only and asymmetrical primary/secondary ports (1-3 PRI, 4 SEC)
02.06.2020

PRODIGY.MC System Update Build 21

This system update replaces the entire system to build 21.

Please follow the update instructions in the Operating Instructions.

Functions

New Features

  • Front panel: Locking function with PIN entry and auto lock
  • Front panel: optional home view with big LTC display (tap on LTC to activate)
  • Auto clock algorithm for automatic sync source changeover
  • Fan control with setting for temperature threshold and silent mode
  • Transparent mode for MADI and NET I/Os for ST2110-31 support
  • IMPROVEMENT: Update now preserves network interface configuration

Bugfixes

  • Front panel: clock source on home screen was not updated correctly under certain circumstances
  • Front panel: encoder turn did not work anymore when display was released from idle state via tap on the screen
22.04.2020

PRODIGY.MP System Update Build 8

This system update replaces the entire system to build 8.

This release requires globcon version 1.2.1

Please follow the update instructions in the Manual.

Functions

  • Compressor/Dynamics added
  • transparent mode for MADI and NET I/Os for ST2110-31 support
  • SFP port support for Management network interface added
  • Fan control with setting for temperature threshold and silent mode
  • Front panel: Locking function with PIN entry and auto lock
  • Front panel: optional home view with big LTC display (tap on LTC to activate)
  • IMPROVEMENT: Update now preserves network interface configuration
  • IMPROVEMENT: Many internal improvements around Flex Channel handling

Bugfixes

  • BUGFIX: clock source changes were not always displayed correctly on front panel
  • BUGFIX: MUTE ALL button was not displayed as active if the MUTE ALL state was left by tapping on one of the MUTE groups instead of the MUTE ALL button
  • IMPROVEMENT/BUGFIX: PAD initialisation during boot (MIC8.x modules)
01.04.2020

PRODIGY RAV.IO Firmware HW 0.14 / SW 0.21

The update refers to the RAVENNA module RAV.IO used in PRODIGY.MC and PRODIGY.MP.

Functions

  • Improved behaviour for redundant PTP handling -> Grandmaster change not only on complete loss of the Grandmaster but also if e.g. the clock class changes
  • improved RTSP compatibility
  • switch configuration can be restored via "Load Preset -> Device" and reset via manufacturer default reset

Bugfixes

  • Output stream status was not displayed correctly <- fixed
  • improved password lock security
  • module could become unreachable on sudden loss of a tcp connection <- fixed
  • improved user interface behaviour when using Safari
  • corrected MIME-types in user interface
  • improved SDP parsing for SDPs for redundant streams
01.04.2020

MONTONE.42 - RAVENNA Module Firmware HW 4.5 / SW 4.25

The update refers to the RAVENNA module used in MONTONE.42 and PRODUCER.COM (equipped with the module optionally).

** This update requires MONTONE.42 main frame firmware 2.4/2.0. **

Functions

New Feature:

  • Improved behaviour for redundant PTP handling -> Grandmaster change not only on complete loss of the Grandmaster but also if e.g. the clock class changes

Bugfixes

    • corrected MIME-types in user interface
    • improved SDP parsing for SDPs for redundant streams

    27.01.2020

    MONTONE.42 - RAVENNA Module Firmware HW 4.5 / SW 4.22

    The update refers to the RAVENNA module used in MONTONE.42 and PRODUCER.COM (equipped with the module optionally).

    ** This update requires MONTONE.42 main frame firmware 2.4/2.0. **

    Functions

    New Feature:

    • PTP Hybrid Mode added (Unicast Delay Requests)

    Bugfixes

    • improved TCP filter to avoid Denial-of-Service attacks
    • fixed a bug in password lock mechanism
    • improved RTSP parser for better compatibility with 3rd party implementations
    • SDP listing in Output Stream Configuration Dialog was not updated correctly <- fixed
    04.12.2019

    PRODIGY.MC System Update Build 20

    This system update replaces the entire system to build 20.

    Please follow the update instructions in the Software Guide.

    Functions

    • Improved idle Display behaviour -> if the screen is dark the first tap on the screen, encoder movement or pressing a button is ignored and just turns on the backlight
    • Improved Watchdog

    Bugfixes

    • Phase reverse fix of FPGA build 66 affected AES outputs also <- fixed
    15.11.2019

    PRODIGY.MC System Update Build 19

    This system update replaces the entire system to build 19.

    Please follow the update instructions in the Software Guide.

    Functions

    • added downloadable Support Archive
    • added watchdog for front panel UI
    • added PAD initialisation during boot

    Bugfixes

    • BUGFIX: 64ch Mode for MADI I/Os did not work properly at 2FS and 4FS
    • BUGFIX: AN8.O Line Outputs were phase reversed
    • BUGFIX: Gain Range of MIC8.LINE modules was not completely available
    • BUGFIX: AES LED still showed blue color for clock master even if there was no input signal available
    14.11.2019

    PRODIGY RAV.IO Firmware HW 0.13 / SW 0.16

    The update refers to the RAVENNA module RAV.IO used in PRODIGY.MC and PRODIGY.MP.

    Bugfixes

    • Bugfix: checksums in PTP messages were not correct <- fixed

    29.10.2019

    PRODIGY RAV.IO Firmware HW 0.13 / SW 0.15

    The update refers to the RAVENNA module RAV.IO used in PRODIGY.MC and PRODIGY.MP.

    Bugfixes

    • fixed channel routing after factory reset
    • minor bugfixes for the User Interface
    • fix for "Network / Audio" LED on PRODIGY front panel
    02.10.2019

    PRODIGY.MC System Update Build 18

    This system update replaces the entire system to build 18.

    Please follow the update instructions in the Software Guide.

    Functions

    • support for all MIC modules

    Bugfixes

    • Gateway setting was not restored after reboot on UI <- fixed
    • noise on Headphone Outputs @4FS <- fixed
    • improved DANTE.IO boot behavior
    23.09.2019

    PRODIGY RAV.IO Firmware HW 0.12 / SW 0.14

    The update refers to the RAVENNA module RAV.IO used in PRODIGY.MC and PRODIGY.MP.

    Functions

    • PTP Hybrid (Mixed) Mode added

    Bugfixes

    • fixed issues with certain DHCP servers

    • improved RTSP parser
    • improved audio interface for stream outputs (TX)
    15.07.2019

    SG.MADI features MIDI Tunnel

    Remote Control of ANDIAMO devices using MIDI tunnel

    Functions

    • MIDI tunnel added to remote control ANDIAMO devices via MADI link

    Use Waves Central to update your SG.MADI device.

    01.07.2019

    EXBOX.MD - Firmware 1.5

    To run the firmware update please download the Dante Firmware Update Manager.

    Before you update your device, make sure you have a backup of the device setup. After the update the device is required to reboot, so audio transmission will be interrupted.

    Functions

    • BNC MADI input can be switched to word clock input
    27.05.2019

    MONTONE.42 - RAVENNA Module Firmware HW 4.5 / SW 4.18

    The update refers to the RAVENNA module used in MONTONE.42 and PRODUCER.COM (equipped with the module optionally).

    ** This update requires MONTONE.42 main frame firmware 2.4/2.0. **

    Functions

    Major New Functions:

    • Support of SMPTE ST 2110-31 (AES3 Transparent Transport) with two transparency modes (CUVP and full transparency)
    • SDP retrieval via HTTP. The SDP information is also displayed in the Stream configuration dialog.
    • Network traffic display, shows current Datarate on RX/TX network port.
    • New Icon (Pause) for pre-configured Backup Streams

    Bugfixes

    • improved TCP stack to cope with ECN flags
    • improved IGMP LEAVE handling for redundant streams that are connected to one port
    • possible CRC-Errors in combination with Cisco Nexus switches <- fixed
    • "Time Stamp out of Bounds" message could show wrong values <- fixed
    05.12.2018

    MONTONE.42 - RAVENNA Module Firmware HW 4.2 / SW 4.11

    The update refers to the RAVENNA module used in MONTONE.42 and PRODUCER.COM (equipped with the module optionally).

    ** This update requires MONTONE.42 main frame firmware 2.0/1.9. **

    Functions

    New Functions:

      • LED warning per stream for "RTP timestamp out of bounds" error

      Bugfixes

      • 2nd Source-IP-Address for SSM could not be configured manually <- fixed
      • IGMP v3 SSM did not work correctly during backup stream switch-over <- fixed
      • IGMP v2Group Specific Query was not answered <- fixed
      • SDP Error Messages were not always displayed correctly <- fixed
      • Single-Port configuration did not work correctly with redundant SDP <- fixed
      • DNS Domain starting with a number were not working correctly <- fixed
      04.12.2018

      EXBOX.MD - Firmware 1.4

      To run the firmware update please download the Dante Firmware Update Manager.

      Before you update your device, make sure you have a backup of the device setup. After the update the device is required to reboot, so audio transmission will be interrupted.

      Functions

      • PSU Status display added
      • DO.Net daemon added
      • Frequency display added
      • Improved behaviour of webUI during device boot

      17.09.2018

      Firmware Update Tool 3.0.1 and Driver 2.12.28 (Windows®)

      Version 3.0.1 / 2.12.28

      Functions

      Firmware Update Tool:

      • Maintenance Update for driver support under Windows 10

      USB Serial Driver:

      • Improved Windows 10 support
      • Improved behaviour on sudden removal of a USB device
      10.09.2018

      MA2CHBOX.XL - Firmware 1.9

      10.09.2018

      MADI.SRC - Firmware 3.0

      Firmware 3.0 - Remote Control

      Functions

      • Remote Control via globcon added
      • HD video sync support
      • seperated clock selection for MADI inputs
      31.07.2018

      ANDIAMO Remote Version 3.5 (Windows®)

      Version 3.5

      Functions

      • New: Front panel brightness adjustment (Dim) support added for ANDIAMO.AES (SRC)

      Bugfixes

        • App crash if more than one DO.Net daemon was found on the network and no device was connected <- fixed
        • ANDIAMO.MC - Gains: Display error when more than 4 ANDIAMO.MCs are connected <- fixed
        20.06.2018

        MADI.9648 - Firmware 1.6

        2 FS signals may use either the 48k Frame (S/MUX) or the 96k Frame (sometimes called ‚high speed‘) format. MADI.9648 detects the frame format at the 2 FS input and sets the 2 FS output accordingly.

        Functions

        - S/MUX support added for ports 1..4
        - Output mute improved

        08.06.2018

        EXBOX.MD - Firmware 1.3

        To run the firmware update please download the Dante Firmware Update Manager.

        Before you update your device, make sure you have a backup of the device setup. After the update the device is required to reboot, so audio transmission will be interrupted.

        Functions

        • EARS - Enhanced Automatic Redundancy Switching
        • MADI Formats: 56 / 57 / 64 channel modes
        • Channel based routing matrix
        09.03.2018

        MONTONE.42 - RAVENNA Module Firmware 3.6 / 3.19

        The update refers to the RAVENNA module used in MONTONE.42 and PRODUCER.COM (equipped with the module optionally).

        ** This update requires MONTONE.42 main frame firmware 2.0/1.9. **

        Functions

        • Please see the comprehensive Release Note document for changes in this update.

        Major new functions:

        • Network interfaces can be separately configured (IP/MAC/Gateway)
        • Streaming and control can be assigned to a certain network interface
        • Redundant audio streaming according to ST2022-7
        • Many other little improvements
        28.02.2018

        EXBOX.MD - Firmware 1.2

        To run the firmware update please download the Dante Firmware Update Manager.

        Before you update your device, make sure you have a backup of the device setup. After the update the device is required to reboot, so audio transmission will be interrupted.

        Bugfixes

        • fixed issues with 44.1 kHz operation
        • includes latest firmware for Brooklyn module (v4.0.8.2)
        08.12.2017

        ANDIAMO 2 (XT/SRC) - Firmware 6.6

        Functions

        • new feature: front panel brightness dimmable
        • improved Mute behavior during startup
        08.12.2017

        ANDIAMO Remote Version 3.4 (Windows®)

        Version 3.4

        Functions

        • New: Front panel brightness adjustable (Dim)

        Bugfixes

          • App hang if no DO.Net daemon was found on the network <- fixed
          • ANDIAMO.MC - Gains: Channel no. above 99 were not displayed correctly
          08.12.2017

          EXBOX.BLDS - Firmware 4.4

          Bugfixes

          • BLDS 1 LED did always blink in Pilote tone mode <- fixed

          • Pilote tone mode did not work at 96kHz <- fixed
          01.11.2017

          MONTONE.42 - RAVENNA Module Firmware 2.7 / 2.23

          The update refers to the RAVENNA module used in MONTONE.42 and PRODUCER.COM (equipped with the module optionally).

          ** This update requires MONTONE.42 main frame firmware 2.0/1.9. **

          Bugfixes

          • Payload size did not match the value in stream configuration <- fixed

          10.10.2017

          ANDIAMO Remote Version 3.3 (Windows®)

          Version 3.3

          Bugfixes

            • Remote window not displayed after device Enumeration via DO.Net <- fixed
            • ANDIAMO.AES Remote window not displayed after Enumeration <- fixed
            • Offline Mode did not work as of version 3.2.1 <- fixed
            09.08.2017

            MONTONE.42 - RAVENNA Module Firmware 2.6 / 2.20

            The update refers to the RAVENNA module used in MONTONE.42 and PRODUCER.COM (equipped with the module optionally).

            ** This update requires MONTONE.42 main frame firmware 2.0/1.9. **

            Functions

            • HTML-based web interface
            • Popup windows to edit related settings (e.g. MADI Out) accessible via hyperlinks 
            • Info display via mouse-over (e.g. PSU)
            • Scalable GUI (lossless zoom) for optimal view on standard or hdpi display
            • Matrix: View Filter added to hide unused I/Os
            • Matrix: N/C line added (Not Connected)
            • Matrix: SHIFT + Click for multi-channel-patches (diagonal and horizontal)
            • Matrix: ALT + Click to de-activate a patch (set to N/C)
            • Lock device: Password protection
            • PTP profiles: default E2E, default P2P, media E2E, media P2P, customized
            • Display of Grandmaster ID (GMID)
            • Gateway support for static and dynamic IP addresses
            • Support of SMPTE/ST2110-30
            02.08.2017

            ANDIAMO Remote Version 3.2 (Windows®)

            Version 3.2

            Bugfixes

              • Wrong device selected after first device enumeration <- fixed.
              27.06.2017

              MADI.9648 - Firmware 1.3

              2 FS signals may use either the 48k Frame (S/MUX) or the 96k Frame (sometimes called ‚high speed‘) format. MADI.9648 detects the frame format at the 2 FS input and sets the 2 FS output accordingly.

              Functions

              - added support for 48k Frame (S/MUX) at the 2 FS I/Os. 

              06.04.2017

              ANDIAMO 2 - Firmware 6.4

              Functions

              • new feature: summing bus with dithering
              • improved behavior of DA-Mutes
              06.04.2017

              ANDIAMO 2.XT - Firmware 6.4

              Functions

              • new feature: summing bus with dithering
              • improved behavior of DA-Mutes
              17.03.2017

              ANDIAMO Remote Version 3.1 (Windows®)

              Version 3.1

              Bugfixes

              • DO.Net: Device Enumeration did not work correctly <- fixed
              • Display errors in Matrix <- fixed
              09.03.2017

              ANNA-LISA - Remote for Android Version 1.5

              A new version (1.5) of ANNA-LISA Remote for ANDROID is ready for download in the Google PlayStore.

              Functions

              • New: 57 channel mode (in Expert Mode)
              • SFP and Channel Status freshened up
              • FPGA Firmware 1.6

              Bugfixes

              • fixed: display problem of BitScope and Levels on Samsung Tab S2 & Google Pixel C
              21.02.2017

              EXBOX.UMA - USB Audio driver macOS®

              Functions

              • support for macOS® 10.12.x (Sierra)
              21.02.2017

              MADI.SRC - Firmware 2.5

              Firmware 2.5 features a De-Embedder / Embedder for serial data

              Functions

              Bypass for embedded serial data (Serial over MADI)

              01.02.2017

              EXBOX.BLDS - Firmware 4.1

              Functions

              New:

               

              GPI Fault detection: If one or more GPIs has contact to GND, the respective yellow LED in the center of the unit flashes quickly during power up.

              Mute output with GPI 1 and 2

              Connecting GPI 1 and GPI 2 to GND mutes output

              Audio Pilot modes:

              Presence of audio signal > -42 dBFS on channel 56 (96kHz: ch. 28) triggers switching. Switching to the port is immediate, switching away after ca. 10 ms. The pilote tone modes are indicated by slowly blinking LOCK LEDs in the Priority section.

              10.01.2017

              PRODUCER.COM Remote Version 1.17

              Version 1.17 of the Firmware for DirectOut PRODUCER.COM is released.

              Functions

              Clock Multiplier (1FS, 2FS, 4FS) follows word clock automatically if WCK is selected as sync source.

              12.12.2016

              ANDIAMO.MC - Firmware 4.7

              Bugfixes

              - issue with remote control for Yamaha AD8HR (Remote Protocol C) <- fixed

              12.12.2016

              ANDIAMO Remote Version 3.0.2 (Windows®)

              Version 3.0.2

              Bugfixes

              • AD/DA Calibration dialog updated for use with ANDIAMO.MC
              • AD/DA Calibration activation did not work reliably <- fixed
              • GUI error on Fastswitch buttons in Gains windows <- fixed
              • ANDIAMO.MC with Dallis firmware did not appear on Fastswitch buttons <- fixed
              24.11.2016

              MADI.BRIDGE - Firmware 2.2

              Functions

              New Feature:

              - Remote Control via MIDI Program Changes

              24.11.2016

              MADI.BRIDGE - Firmware 2.4

              Functions

              New Feature:

              - signal mute when switching

              - improved input sensitivity

              23.11.2016

              ANDIAMO.MC - Firmware 4.6

              23.11.2016

              ANDIAMO 2 - Firmware 6.1

              Bugfixes

              - phase reverse issue at analog output (only devices with new DA converters) <= fixed

              23.11.2016

              ANDIAMO 2.XT - Firmware 6.1

              Bugfixes

              - phase reverse issue at analog output (only devices with new DA converters) <= fixed

              23.11.2016

              ANDIAMO 2.AD & DA - Firmware 1.5

              23.11.2016

              ANDIAMO.AES - Firmware 2.7

              Functions

              - User Bit Transport automatic set to ‚REM‘ in the background, if the USB Embedder is active

              21.10.2016

              ANDIAMO.MC - Firmware 4.4

              The new features are accessible with ANDIAMO Remote v3.0 (Windows®) or higher.

              Functions

              - new: defeat delay compensation

              - modified: level meter: low level start @ -60dBFs

              Bugfixes

              - issue with device activation < fixed

              - issue with embedder for MIDI-over-MADI < fixed

              19.09.2016

              ANDIAMO Remote Version 3.0 (Windows®)

              Version 3.0

              Functions

              • Switch to deactivate Delay Compensation added.
              • Improved UI update when switching between devices.
              • Fast Switch buttons in Gains window allow switching between up to 4 devices. The device name on the button is taken from the device name given in the Device Manager.
              • Project Files allow to save and restore settings of all currently connected devices. Missing units will be skipped when loading a project file.
              • Snapshot function for gain settings. A snapshot contains all gain settings of all currently connected devices.
              • New program setting to deactivate click&drag behaviour in the matrix. Only one crosspoint is set at a time.

              Bugfixes

              • Settings dialog: 'Cancel' still changed settings if the device's status had not been queried before (e.g. when switching to the second unit in a chain). <- fixed. Also settings dialog can not be accessed until the current status has been queried successfully.
              • Devicelist file could not be saved under certain circumstances <- missing user rights to write file in program file directory -> Devicelist is now stored in /AppData directory.
              • Redundancy Settings: 'Force to MADI x' got changed to 'Prio to MADI x' if 'Force to MADI x' was already selected before. <- fixed
              • Transmission of current settings when switching from offline mode to online mode does not work as expected <- This function is not compatible anymore with the way how multiple devices are enumerated. It has been replaced by a request to save a preset file.
              05.09.2016

              MA2CHBOX.XL - Firmware 1.8

              Functions

              New:

              - improved Muting on power on / power off as of hardware revision 1.2

              26.07.2016

              MA2CHBOX - Firmware 3.3 (alternative firmware)

              26.07.2016

              MA2CHBOX.XT - Firmware 3.3 (alternative firmware)

              26.05.2016

              PRODUCER.COM Remote Version 1.6

               

              Version 1.6 of the Remote Software for DirectOut PRODUCER.COM is released.

              Functions

              Aux Output routing now supports busses as source (e.g. talkback or listen).

              06.01.2016

              ANDIAMO Remote Version 2.8.2 (Windows®)

              Version 2.8.2

              Functions

              • Extended Routing did not work with ANDIAMO.MC that use firmware version 4.x <- fixed
              • DO.Net - modified TTL value (128) to address issues in networks environments with more than one switch.