NOTE: This update requires build 27 and update mode v1.3.2 to be installed first.

Please follow the update instructions in the Manual.

Bugfixes

• Issue with the Output of FastSRC <= fixed (FPGA Firmware v1.1 Build 35)
• Hotfix for License Manager

NOTE: This update requires build 13 and update mode v1.3.2 to be installed first.

Please follow the update instructions in the Manual.

Bugfixes

• Issue with the Output of FastSRC <= fixed (FPGA Firmware v1.2 Build 54)
• Hotfix for License Manager

Update 12.07.2021 - black front panel version only.

Before you update your device, make sure you have a full config backup of your data. During the update the device will reboot, so audio transmission will be interrupted.

The update procedure is described on page 32 of the Hardware & Installation Guide.

It's essential to clear the browser cache after the update.

Functions

• FPGA Firmware v3.8 Build 8 improves MADI receiver

Bugfixes

• port assignment of primary fallback configuration for clock redundancy did not work properly

NOTE: This update requires build 12 and update mode v1.3.2 to be installed first.

This system update replaces the entire system to build 13.

This release requires globcon version 1.7.0 - please use the installer added here (macOS / Windows).

Please follow the update instructions in the Manual.

Functions

NOTE: This update requires build 26 and update mode v1.3.2 to be installed first.

This system update replaces the entire system to build 27.

This release requires globcon version 1.7.0 - please use the installer added here (macOS / Windows).

Please follow the update instructions in the Manual.

Functions

• Input Managers with silence detection
• Automatic Bypass for FastSRC(TM)
• Loudness Metering (license option)

This system update replaces the entire system to build 12.

This release requires globcon version 1.6.0

Please follow the update instructions in the Manual.

Functions

Bugfixes

This system update replaces the entire system to build 26.

This release requires globcon version 1.6.0.

Please follow the update instructions in the Manual.

Functions

• Front panel: signal present indicator in levelmeters aligned with globcon levelmeters
• Front panel: license information page with info about license state on the device
• Remote control: Ember+ service
• Remote control: OSC service

Bugfixes

• Front panel: levelmeter flickering with static signals (e.g. sine wave) <- fixed
• Front panel: graphical module label wrap-around for certain module types <- fixed

The update refers to the RAVENNA module RAV.IO used in PRODIGY.MC and PRODIGY.MP.

Functions

New:

• NMOS IS-04 / IS-05 support added

Bugfixes

• TTL for SAP and RTCP was always "1"
• Fix for Gateway assignment to both NICs
• MAC assignment for unicast RTP packets did not work, if packets wer sent over Gateway
• Avoid duplicate SAP hashes through improved algorithm
• No SAP deletion packet on Grandmaster change
• Offset Fine value initialisation in web UI not correct
• Fix for stream label display in Google Chrome
• Label "Port 1/2" changed to "NIC 1/2" to distinct between switch port and NIC

Functions

New:

• NMOS IS-04 / IS-05 support added

Bugfixes

• TTL for SAP and RTCP was always "1"
• Fix for Gateway assignment to both NICs
• MAC assignment for unicast RTP packets did not work, if packets wer sent over Gateway
• Avoid duplicate SAP hashes through improved algorithm
• No SAP deletion packet on Grandmaster change
• Offset Fine value initialisation in web UI not correct
• Fix for stream label display in Google Chrome
• Label "Port 1/2" changed to "NIC 1/2" to distinct between switch port and NIC

The update refers to the RAVENNA module used in MONTONE.42 and PRODUCER.COM (equipped with the module optionally).

** This update requires MONTONE.42 main frame firmware 2.4/2.0. **

Functions

New:

• Port routing via Ctrl+Click in Matrix
• Hardware filter for PTP Delay Requests and Responses of other devices in the network

Bugfixes

• improved hash algorithm for SAP packets
• no SAP deletion on Grandmaster change
• fixed wrong time stamping in PTP P2P packets
• don't send PTP follow-up messages in One-Step clock mode
• improved stream label display in Google Chrome

This system update replaces the entire system to build 11.

This release requires globcon version 1.5.0

Please follow the update instructions in the Manual.

Functions

Bugfixes

This system update replaces the entire system to build 25.

This release requires globcon version 1.5.0.

Please follow the update instructions in the Manual.

Functions

• Snapshots can be stored in the device and recalled stand-alone from the front panel
• Operation: "Configuration" and "Show" Mode
• Ember+
• OSC

Bugfixes

• improved MADI receiver
• improved file handling for configuration data

This system update replaces the entire system to build 10.

This release requires globcon version 1.4.0

Please follow the update instructions in the Manual.

Functions

Bugfixes

This system update replaces the entire system to build 23.

This release requires globcon version 1.4.0.

Please follow the update instructions in the Operating Instructions.

Functions

• GROUPS: Outputs can be assigned to up to 16 groups
• basic MIDI-over-MADI control support (Gains, P48, PAD -> use PRODIGY MIDI PlugIn in globcon)
• improved Fan speed measurement

Bugfixes

• improved DA Mute during power-on
• AoIP modules could be set and held in reset state after several weeks without reboot <- fixed
• FrontPanel: Output Levelmeters did not work <- fixed
• FrontPanel: Phones Mute Button was not updated correctly in all cases <- fixed

Update 31.07.2020 - black front panel version only.

This update requires the previous update (07.04.2019) being installed.

Before you update your device, make sure you have a full config backup of your data. During the update the device will reboot, so audio transmission will be interrupted.

The update procedure is described on page 32 of the Hardware & Installation Guide.

It's essential to clear the browser cache after the update.

Bugfixes

• port assignment of primary fallback configuration for clock redundancy did not work properly

Version 2.4.2

Functions

USB Serial Driver:

• Improved behaviour on sudden removal of a USB device

This system update replaces the entire system to build 22.

Please follow the update instructions in the Operating Instructions.

Functions

• Fast SRCs (bidirectional low latency asynchronous SRC) for MADI and NET I/Os
• MIDI-Matrix (incl. support for MIDI-over-MADI tunneling)
• LTC to MTC converter
• Sine wave, Pink noise and white noise generators
• Enhanced Automatic Redundancy Switching (EARS) for NET and MADI I/Os
• Levelmeter speed configuration

Bugfixes

• Lock state not preserved on page reload via Browser <- fixed
• Bit transparency for ST2110-31 and AES I/Os did not work properly <- fixed
• improved globcon bridge startup behavior

The update refers to the RAVENNA module RAV.IO used in PRODIGY.MC and PRODIGY.MP.

Functions

New:

• IP Mode for PTP: Unicast

Bugfixes

The update refers to the RAVENNA module used in MONTONE.42 and PRODUCER.COM (equipped with the module optionally).

** This update requires MONTONE.42 main frame firmware 2.4/2.0. **

Functions

New:

• IP Mode for PTP: Unicast

This system update replaces the entire system to build 9.

This release requires globcon version 1.3.0

Please follow the update instructions in the Manual.

Functions

Bugfixes

To run the firmware update please download the Dante Firmware Update Manager or you may use the update function which is integrated in the Dante Controller.

The firmware update procedure is described in the manual (Appendix D).

Before you update your device, make sure you have a backup of the device setup. After the update the device is required to reboot, so audio transmission will be interrupted.

Functions

• Fast SRC for Dante I/O
• new VLAN configurations for control on port 4 only and asymmetrical primary/secondary ports (1-3 PRI, 4 SEC)

This system update replaces the entire system to build 21.

Please follow the update instructions in the Operating Instructions.

Functions

New Features

• Front panel: Locking function with PIN entry and auto lock
• Front panel: optional home view with big LTC display (tap on LTC to activate)
• Auto clock algorithm for automatic sync source changeover
• Fan control with setting for temperature threshold and silent mode
• Transparent mode for MADI and NET I/Os for ST2110-31 support
• IMPROVEMENT: Update now preserves network interface configuration

Bugfixes

• Front panel: clock source on home screen was not updated correctly under certain circumstances
• Front panel: encoder turn did not work anymore when display was released from idle state via tap on the screen

This system update replaces the entire system to build 8.

This release requires globcon version 1.2.1

Please follow the update instructions in the Manual.

Functions

Bugfixes

The update refers to the RAVENNA module RAV.IO used in PRODIGY.MC and PRODIGY.MP.

Functions

• Improved behaviour for redundant PTP handling -> Grandmaster change not only on complete loss of the Grandmaster but also if e.g. the clock class changes
• improved RTSP compatibility
• switch configuration can be restored via "Load Preset -> Device" and reset via manufacturer default reset

Bugfixes

• Output stream status was not displayed correctly <- fixed
• improved password lock security
• module could become unreachable on sudden loss of a tcp connection <- fixed
• improved user interface behaviour when using Safari
• corrected MIME-types in user interface
• improved SDP parsing for SDPs for redundant streams

The update refers to the RAVENNA module used in MONTONE.42 and PRODUCER.COM (equipped with the module optionally).

** This update requires MONTONE.42 main frame firmware 2.4/2.0. **

Functions

New Feature:

• Improved behaviour for redundant PTP handling -> Grandmaster change not only on complete loss of the Grandmaster but also if e.g. the clock class changes

Bugfixes

• corrected MIME-types in user interface
• improved SDP parsing for SDPs for redundant streams

The update refers to the RAVENNA module used in MONTONE.42 and PRODUCER.COM (equipped with the module optionally).

** This update requires MONTONE.42 main frame firmware 2.4/2.0. **

Functions

New Feature:

• PTP Hybrid Mode added (Unicast Delay Requests)

Bugfixes

• improved TCP filter to avoid Denial-of-Service attacks
• fixed a bug in password lock mechanism
• improved RTSP parser for better compatibility with 3rd party implementations
• SDP listing in Output Stream Configuration Dialog was not updated correctly <- fixed

This system update replaces the entire system to build 20.

Please follow the update instructions in the Software Guide.

Functions

• Improved idle Display behaviour -> if the screen is dark the first tap on the screen, encoder movement or pressing a button is ignored and just turns on the backlight
• Improved Watchdog

Bugfixes

• Phase reverse fix of FPGA build 66 affected AES outputs also <- fixed

This system update replaces the entire system to build 19.

Please follow the update instructions in the Software Guide.

Functions

• added downloadable Support Archive
• added watchdog for front panel UI
• added PAD initialisation during boot

Bugfixes

• BUGFIX: 64ch Mode for MADI I/Os did not work properly at 2FS and 4FS
• BUGFIX: AN8.O Line Outputs were phase reversed
• BUGFIX: Gain Range of MIC8.LINE modules was not completely available
• BUGFIX: AES LED still showed blue color for clock master even if there was no input signal available

The update refers to the RAVENNA module RAV.IO used in PRODIGY.MC and PRODIGY.MP.

Bugfixes

• Bugfix: checksums in PTP messages were not correct <- fixed

The update refers to the RAVENNA module RAV.IO used in PRODIGY.MC and PRODIGY.MP.

Bugfixes

• fixed channel routing after factory reset
• minor bugfixes for the User Interface
• fix for "Network / Audio" LED on PRODIGY front panel

This system update replaces the entire system to build 18.

Please follow the update instructions in the Software Guide.

Functions

• support for all MIC modules

Bugfixes

• Gateway setting was not restored after reboot on UI <- fixed
• noise on Headphone Outputs @4FS <- fixed
• improved DANTE.IO boot behavior

The update refers to the RAVENNA module RAV.IO used in PRODIGY.MC and PRODIGY.MP.

Functions

• PTP Hybrid (Mixed) Mode added

Bugfixes

• fixed issues with certain DHCP servers

• improved RTSP parser
• improved audio interface for stream outputs (TX)

Remote Control of ANDIAMO devices using MIDI tunnel

Functions

• MIDI tunnel added to remote control ANDIAMO devices via MADI link

Use Waves Central to update your SG.MADI device.

To run the firmware update please download the Dante Firmware Update Manager.

Before you update your device, make sure you have a backup of the device setup. After the update the device is required to reboot, so audio transmission will be interrupted.

Functions

• BNC MADI input can be switched to word clock input

The update refers to the RAVENNA module used in MONTONE.42 and PRODUCER.COM (equipped with the module optionally).

** This update requires MONTONE.42 main frame firmware 2.4/2.0. **

Functions

Major New Functions:

• Support of SMPTE ST 2110-31 (AES3 Transparent Transport) with two transparency modes (CUVP and full transparency)
• SDP retrieval via HTTP. The SDP information is also displayed in the Stream configuration dialog.
• Network traffic display, shows current Datarate on RX/TX network port.
• New Icon (Pause) for pre-configured Backup Streams

Bugfixes

• improved TCP stack to cope with ECN flags
• improved IGMP LEAVE handling for redundant streams that are connected to one port
• possible CRC-Errors in combination with Cisco Nexus switches <- fixed
• "Time Stamp out of Bounds" message could show wrong values <- fixed

The update refers to the RAVENNA module used in MONTONE.42 and PRODUCER.COM (equipped with the module optionally).

** This update requires MONTONE.42 main frame firmware 2.0/1.9. **

Functions

New Functions:

• LED warning per stream for "RTP timestamp out of bounds" error

Bugfixes

• 2nd Source-IP-Address for SSM could not be configured manually <- fixed
• IGMP v3 SSM did not work correctly during backup stream switch-over <- fixed
• IGMP v2Group Specific Query was not answered <- fixed
• SDP Error Messages were not always displayed correctly <- fixed
• Single-Port configuration did not work correctly with redundant SDP <- fixed
• DNS Domain starting with a number were not working correctly <- fixed

To run the firmware update please download the Dante Firmware Update Manager.

Before you update your device, make sure you have a backup of the device setup. After the update the device is required to reboot, so audio transmission will be interrupted.

Functions

• PSU Status display added
• DO.Net daemon added
• Frequency display added
• Improved behaviour of webUI during device boot
  

Version 3.0.1 / 2.12.28

Functions

Firmware Update Tool:

• Maintenance Update for driver support under Windows 10

USB Serial Driver:

• Improved Windows 10 support
• Improved behaviour on sudden removal of a USB device

Functions

New:

- support for globcon added

Firmware 3.0 - Remote Control

Functions

• Remote Control via globcon added
• HD video sync support
• seperated clock selection for MADI inputs

Version 3.5

Functions

• New: Front panel brightness adjustment (Dim) support added for ANDIAMO.AES (SRC)

Bugfixes

• App crash if more than one DO.Net daemon was found on the network and no device was connected <- fixed
• ANDIAMO.MC - Gains: Display error when more than 4 ANDIAMO.MCs are connected <- fixed

2 FS signals may use either the 48k Frame (S/MUX) or the 96k Frame (sometimes called ‚high speed‘) format. MADI.9648 detects the frame format at the 2 FS input and sets the 2 FS output accordingly.

Functions

- S/MUX support added for ports 1..4
- Output mute improved

To run the firmware update please download the Dante Firmware Update Manager.

Before you update your device, make sure you have a backup of the device setup. After the update the device is required to reboot, so audio transmission will be interrupted.

Functions

The update refers to the RAVENNA module used in MONTONE.42 and PRODUCER.COM (equipped with the module optionally).

** This update requires MONTONE.42 main frame firmware 2.0/1.9. **

Functions

• Please see the comprehensive Release Note document for changes in this update.

Major new functions:

• Network interfaces can be separately configured (IP/MAC/Gateway)
• Streaming and control can be assigned to a certain network interface
• Redundant audio streaming according to ST2022-7
• Many other little improvements

To run the firmware update please download the Dante Firmware Update Manager.

Before you update your device, make sure you have a backup of the device setup. After the update the device is required to reboot, so audio transmission will be interrupted.

Bugfixes

• fixed issues with 44.1 kHz operation
• includes latest firmware for Brooklyn module (v4.0.8.2)

Functions

Version 3.4

Functions

• New: Front panel brightness adjustable (Dim)

Bugfixes

• App hang if no DO.Net daemon was found on the network <- fixed
• ANDIAMO.MC - Gains: Channel no. above 99 were not displayed correctly

Bugfixes

• BLDS 1 LED did always blink in Pilote tone mode <- fixed

• Pilote tone mode did not work at 96kHz <- fixed

The update refers to the RAVENNA module used in MONTONE.42 and PRODUCER.COM (equipped with the module optionally).

** This update requires MONTONE.42 main frame firmware 2.0/1.9. **

Bugfixes

• Payload size did not match the value in stream configuration <- fixed

Version 3.3

Bugfixes

• Remote window not displayed after device Enumeration via DO.Net <- fixed
• ANDIAMO.AES Remote window not displayed after Enumeration <- fixed
• Offline Mode did not work as of version 3.2.1 <- fixed

The update refers to the RAVENNA module used in MONTONE.42 and PRODUCER.COM (equipped with the module optionally).

** This update requires MONTONE.42 main frame firmware 2.0/1.9. **

Functions

• HTML-based web interface
• Popup windows to edit related settings (e.g. MADI Out) accessible via hyperlinks 
• Info display via mouse-over (e.g. PSU)
• Scalable GUI (lossless zoom) for optimal view on standard or hdpi display
• Matrix: View Filter added to hide unused I/Os
• Matrix: N/C line added (Not Connected)
• Matrix: SHIFT + Click for multi-channel-patches (diagonal and horizontal)
• Matrix: ALT + Click to de-activate a patch (set to N/C)
• Lock device: Password protection
• PTP profiles: default E2E, default P2P, media E2E, media P2P, customized
• Display of Grandmaster ID (GMID)
• Gateway support for static and dynamic IP addresses
• Support of SMPTE/ST2110-30

Version 3.2

Bugfixes

• Wrong device selected after first device enumeration <- fixed.

2 FS signals may use either the 48k Frame (S/MUX) or the 96k Frame (sometimes called ‚high speed‘) format. MADI.9648 detects the frame format at the 2 FS input and sets the 2 FS output accordingly.

Functions

- added support for 48k Frame (S/MUX) at the 2 FS I/Os. 

Functions

Functions

Version 3.1

Bugfixes

• DO.Net: Device Enumeration did not work correctly <- fixed
• Display errors in Matrix <- fixed

A new version (1.5) of ANNA-LISA Remote for ANDROID is ready for download in the Google PlayStore.

Functions

• New: 57 channel mode (in Expert Mode)
• SFP and Channel Status freshened up
• FPGA Firmware 1.6

Bugfixes

Functions

• support for macOS® 10.12.x (Sierra)

Firmware 2.5 features a De-Embedder / Embedder for serial data

Functions

Bypass for embedded serial data (Serial over MADI)

Functions

New:

GPI Fault detection: If one or more GPIs has contact to GND, the respective yellow LED in the center of the unit flashes quickly during power up.

Mute output with GPI 1 and 2

Connecting GPI 1 and GPI 2 to GND mutes output

Audio Pilot modes:

Presence of audio signal > -42 dBFS on channel 56 (96kHz: ch. 28) triggers switching. Switching to the port is immediate, switching away after ca. 10 ms. The pilote tone modes are indicated by slowly blinking LOCK LEDs in the Priority section.

Version 1.17 of the Firmware for DirectOut PRODUCER.COM is released.

Functions

Clock Multiplier (1FS, 2FS, 4FS) follows word clock automatically if WCK is selected as sync source.

Bugfixes

- issue with remote control for Yamaha AD8HR (Remote Protocol C) <- fixed

Version 3.0.2

Bugfixes

• AD/DA Calibration dialog updated for use with ANDIAMO.MC
• AD/DA Calibration activation did not work reliably <- fixed
• GUI error on Fastswitch buttons in Gains windows <- fixed
• ANDIAMO.MC with Dallis firmware did not appear on Fastswitch buttons <- fixed

Functions

New Feature:

- Remote Control via MIDI Program Changes

Functions

New Feature:

- signal mute when switching

- improved input sensitivity

Bugfixes

- phase reverse issue at analog output (only devices with new DA converters) <= fixed

Bugfixes

- phase reverse issue at analog output (only devices with new DA converters) <= fixed

Bugfixes

- phase reverse issue at analog output (only devices with new DA converters) <= fixed

Bugfixes

- phase reverse issue at analog output (only devices with new DA converters) <= fixed

Functions

- User Bit Transport automatic set to ‚REM‘ in the background, if the USB Embedder is active

The new features are accessible with ANDIAMO Remote v3.0 (Windows®) or higher.

Functions

- new: defeat delay compensation

- modified: level meter: low level start @ -60dBFs

Bugfixes

- issue with device activation < fixed

- issue with embedder for MIDI-over-MADI < fixed

Version 3.0

Functions

• Switch to deactivate Delay Compensation added.
• Improved UI update when switching between devices.
• Fast Switch buttons in Gains window allow switching between up to 4 devices. The device name on the button is taken from the device name given in the Device Manager.
• Project Files allow to save and restore settings of all currently connected devices. Missing units will be skipped when loading a project file.
• Snapshot function for gain settings. A snapshot contains all gain settings of all currently connected devices.
• New program setting to deactivate click&drag behaviour in the matrix. Only one crosspoint is set at a time.

Bugfixes

• Settings dialog: 'Cancel' still changed settings if the device's status had not been queried before (e.g. when switching to the second unit in a chain). <- fixed. Also settings dialog can not be accessed until the current status has been queried successfully.
• Devicelist file could not be saved under certain circumstances <- missing user rights to write file in program file directory -> Devicelist is now stored in /AppData directory.
• Redundancy Settings: 'Force to MADI x' got changed to 'Prio to MADI x' if 'Force to MADI x' was already selected before. <- fixed
• Transmission of current settings when switching from offline mode to online mode does not work as expected <- This function is not compatible anymore with the way how multiple devices are enumerated. It has been replaced by a request to save a preset file.

Functions

New:

- improved Muting on power on / power off as of hardware revision 1.2

Bugfixes

- Menu navigation corrected

- Phones out: phase reverse corrected

Bugfixes

- Menu navigation corrected

- Phones out: phase reverse corrected

Version 1.6 of the Remote Software for DirectOut PRODUCER.COM is released.

Functions

Aux Output routing now supports busses as source (e.g. talkback or listen).

Version 2.8.2

Functions

• Extended Routing did not work with ANDIAMO.MC that use firmware version 4.x <- fixed
• DO.Net - modified TTL value (128) to address issues in networks environments with more than one switch.